Announcements
Thread Rating:
  • 9 Vote(s) - 2.89 Average
  • 1
  • 2
  • 3
  • 4
  • 5
D-series Torque Specs
#1
ALL TOQUE SPECS ARE IN FT-LB.

A/T Tranny Drain plug......................... 29
M/T Tranny Drain and fill plug..............30-40
Wheel Lug Nuts....................................80
Fuel Filter
Banjo Bolt............................................16
Service Bolt.........................................9
Clamp Bolt...........................................9

Valve cover Bolts...................................7
Spark Plugs..........................................13
Cam Gear Bolt.......................................27
Cam cover crown nuts.............................7
Crank(vibration) damper bolt...................119
Cylinder Head Studs....................1st step..22...2nd..49
Flywheel Bolts M/T................................76
Drive Plate bolts for A/T........................54
Header Bolts to Cylinder Head................22
Header to downpipe bolts.......................33
Intake Manifold Bolts..............................16
Oil Pan bolts...........................................9
Oil pick up tube bolts..............................17
Oil Pump to engine block bolts/nuts...........9
Oil Pump Screen bolts..............................8
Oil pump cover Screws.............................5
Oil filter Housing Bolts..............................9
Rocker arm shaft pedestal bolts................16
Rocker arm shaft end caps bolts................9
Timing belt adjstment bolt.........................31
Rod Bolts............................................. ....23

Main Bearings cap bolts
Separate caps and bridge..........................48
One piece cap assembly............................33
Water pump pulley bolts.............................9
Thersmostat housing bolts..........................9
Water pump attaching bolts.........................9

Fuel injection service bolts
88-90................................................ ......9
91up.............................................. ..........11
Throttle Body nuts.....................................16
Fuel Rail nut..............................................9

Manual Transmission
Countershaft locknuts................................65
End cover bolts.........................................9
Selector arm holder bolts...........................9
Tranny case to Flywhee housing..................20
Tranny to engine bolts
4 speed............................................. ........33
5 speed............................................. ........50
Clutch pressure plate bolts...........................19
Release fork bolts........................................22
Driveaxle/hub nuts.......................................134

Brake hose to caliper banjo bolts (front/Rear)...25
Master Cylinder Mounting nuts.......................11
Brake Booster mounting nuts.........................9
Reply
#2
nice info for Ds
Reply
#3
I had to look up oil pan tq specs and i didnt see it on here.. so i fugured what the hell, someone might need this also
Reply
#4
nice this helped my boy last week thanks Rob
Reply
#5
Do you know the specs for the struts and everything am putting in my teins hopfully
I live my life a quarter pounder at a time nothing else matters.
at the end of the day its my car i see it everyday i drive it every day so feel free to express your opinion but dont hate on me for expressing my style Smile
Reply
#6
the teins dont say in the instructions?
Reply
#7
(01-18-2012, 11:04 AM)EsotericImage Wrote:  the teins dont say in the instructions?

havent looked at them clear just skimmed threw them all double check and let you know. is it bad if there not torqued down?
I live my life a quarter pounder at a time nothing else matters.
at the end of the day its my car i see it everyday i drive it every day so feel free to express your opinion but dont hate on me for expressing my style Smile
Reply
#8
Just tighten them until you feel like its good. I never go by spec on that kinda stuff and mines fine
insert cool sig pic here
SquadMember#715 CGPV2.0Member#1 Rice --> Nice[ish] Build Thread
Reply
#9
(01-19-2012, 04:35 AM)TerriYockee Wrote:  Just tighten them until you feel like its good. I never go by spec on that kinda stuff and mines fine

alright thanks for the help man i was freaking out and didnt want to buy a torque wrench Lol
I live my life a quarter pounder at a time nothing else matters.
at the end of the day its my car i see it everyday i drive it every day so feel free to express your opinion but dont hate on me for expressing my style Smile
Reply
 




Users browsing this thread: 1 Guest(s)

About EJ8 Squad